Hand_Soldering_Systems

Convection Rework

Handheld & Systems

APR-1200A-SRS-MOB.jpg
Scorpion Rework System with Reflow heater, Preheater, SmartPlace Technology Camera (Mobile), and Precision Automatic Placement Package

APR-1200A-SRS-MOB


The Scorpion Advanced Package Rework System ensures both accurate component placement and custom tailored reflow profiles in one user friendly, single platform rework system. The Scorpion System redefines precision and addresses the technical demands presented by component manufacturers today.

 

The challenges of array package rework, and the inability to easily inspect placement accuracy, call for a solution that allows for simultaneous viewing of Printed Circuit Board pads and component balls for accurate placement.

 

The Scorpion Rework System fills this need with quick,accurate placement through the use of an all new vision system employing dual image overlay technology. This new vision system features LED lighting both top and bottom for shadow-free component visualization and component alignment. The HD camera is ready to go out of the box.

 

The two-head modular design allows the Scorpion ReworkSystem to be tailored to the users specific rework needs and allows precision alignment of the smallest BGAs, QFNs and Micro SMDs with the highest accuracy. The open-ended board holder fits a wide variety of large, small and odd-shaped boards while allowing precise positioning over the patented dual subzone preheater.

 

The standard auto-profile mode ensures fast and easy profile creation with a minimum of setup time. By selecting your temperature targets any operator can quickly and accurately create reflow profiles for a wide variety of boards, and then save them in memory for future use.

 

Source temperatures and time intervals can be modified and added “On-the-Fly"eliminating the need to wait for the current profile to terminate before modifications can be made. The profiles can range from a simple four zones to a complex reflow oven style profile. Precise solder joint temperatures are measured and displayed on a real time graphical display, thus providing the necessary data to accurately and easily establish the optimum reflow profile for each particular application within minutes. 

 

The modular design of the Scorpion Rework System allows it to be configured to the users’ specific needs. The two-head systems,APR-1200-SRS, APR-1200A-SRS & APR-1200A-SRS-MOB, feature placement accuracy to 0.0015" (.038mm).The standard single-head system,APR-1100-SRS, provides placement accuracy to0.004" (.1mm).

 

The Scorpion system accepts the full range of APR and QX series reflow nozzles. Flux transfer plates and solder paste plates are available to ensure repeatable process control during the replacement operation.


HARDWARE FEATURES

  • Desktop sized
  • 2800W dualzone preheater with 550W top heater
  • 208-240VAC,50/60Hz, 15A-13A, Single Phase
  • Modular design allowing the customer to customize the unit to meet their needs
  • A 343mm(13.5") x open-ended PCB holder with micrometer adjustment
  • Mechanical X and Z axis movement on linear bearings for long-life and minimal maintenance
  • Component is retracted automatically at the end of reflow when removing parts
  • Linux-based integral computer
  • External USB for file transfer
  • SmartPlace Vision System is a high definition vision system which uses dual CMOS sensors to assist in the placement of  components and requires no calibration.

 

NEW FEATURES

  • Motorized Final Placement: Final placement module capable of 50mm of motorized travel in the Z-axis and a full 360° in ϴ (Theta).
  • Force FeedbackControl: Enables the unit to accurately pick and place components without disturbing the component or solder.
  • Component Alignment: Fine motor control of .005”/.127mm in the Z-axis & 0.25° ϴduring alignment of the component to the pad.
  • Redesigned Remote Control: The new remote control incorporates the controls for the placement module and adds new digital controls for the top & bottom LED lighting of the camera module.

 

SMARTPLACE TECHNOLOGY VISION SYSTEM FEATURES

  • Dual, full color HD camera
  • Selectable camera view
  • Diffused LED lighting for shadow-free component alignment

 

NEW FEATURES

  • SmartPlaceTechnology Vision System for Mobile Products: a 1080p, high definition, camerasystem that enables the operator to align and position components accuratelybefore placement. Ideal for use with the smaller packages commonly used inmobile devices up to 25mm x 25mm

 

SOFTWARE FEATURES

  • Auto-Profiling allows operators the ability to create successful reflow profiles the first time
  • On the fly profile management of target set points, adding and subtracting time zones, and profile measurement points
  • Real time graphical display of solder joint temperatures
  • Internal storage of profile data with expansion and transfer via a USB flash drive
  • Graphics-based user interface for simple operation
  • Password protection with multi privilege levels

 

OPERATION FEATURES

  • Uses existing APR-5000 Series reflow and vacuum nozzles
  • Precision Placement head uses pick and place machine nozzles
  • Compact footprint for easy bench top use
  • Self-contained machine, no air supply needed. Plug it in and it is ready to operate.

 

SPECIFICATIONS

Input Voltage

208-240VAC, 50/60Hz, 15 Amp Single Phase

Power Consumption

System Total

2800W (average power)

Inner Zone

900W (heater rating)

Outer Zone

1800W (heater rating)

 Reflow Heater

550W (heater rating)

Operating Temperature

41°F (5°C) to 104°F (40°C)

Maximum Relative humidity

80% at 88°F (31°C) decreasing linearly to 50% at 104°F (40°C)

Maximum Altitude

6500 ft. (2km)

Pollution Degree

2 per IEC 644

Insulation category

II

Temperature Control Type

Closed-Loop Control (Thermocouple)

Maximum Source Temperature

Reflow Head

400°C (752°F)

Pre-Heater (Inner/Outer)

350°C (662°F)

   Airflow

Control

Low, Medium, & High

Supply

24V DC Blower

Component Handling

Maximum Field of View

1.77" x 1.77" (45mm x 45mm)

Minimum Size

0.020" x 0.010" (0.51mm x 0.25mm)

Maximum Weight

1.94 oz. (55 g)

  PCB Handling Capability

              Maximum Size

13.5" x open (342.9 mm x open)

12" x open (304.8 mm x open) for APR-1200A-SRS-MOB only

Maximum Thickness

0.25" (6mm)

System Dimensions  W x D x H

18" x 22" x 26" (457mm x 559mm x 660mm)

Weight

140lbs (63.5kg)

System Warranty

One-year parts & labor  90 days heaters & lamps

Input Voltage

208-240VAC, 50/60Hz, 15 Amp Single Phase

Power Consumption

System Total

2800W (average power)

Inner Zone

900W (heater rating)

Outer Zone

1800W (heater rating)

 Reflow Heater

550W (heater rating)

Operating Temperature

41°F (5°C) to 104°F (40°C)

Maximum Relative humidity

80% at 88°F (31°C) decreasing linearly to 50% at 104°F (40°C)

Maximum Altitude

6500 ft. (2km)

Pollution Degree

2 per IEC 644

Insulation category

II

Temperature Control Type

Closed-Loop Control (Thermocouple)

Maximum Source Temperature

Reflow Head

400°C (752°F)

Pre-Heater (Inner/Outer)

350°C (662°F)

   Airflow

Control

Low, Medium, & High

Supply

24V DC Blower

Component Handling

Maximum Field of View

1.77" x 1.77" (45mm x 45mm)

Minimum Size

0.020" x 0.010" (0.51mm x 0.25mm)

Maximum Weight

1.94 oz. (55 g)

  PCB Handling Capability

              Maximum Size

13.5" x open (342.9 mm x open)

12" x open (304.8 mm x open) for APR-1200A-SRS-MOB only

Maximum Thickness

0.25" (6mm)

System Dimensions  W x D x H

18" x 22" x 26" (457mm x 559mm x 660mm)

Weight

140lbs (63.5kg)

System Warranty

One-year parts & labor  90 days heaters & lamps


Accessories included with APR-1200A-SRS:

  • FSL-SRS-3 Spring PCB Finger Long (Pack 3)
  • FSS-SRS-3 Spring PCB Finger Short (Pack 3)
  • AC-TCK-40-36 Thermocouple, 40 Gauge (Pack 3)
  • VNZ-ORINGK O-Ring Kit (assortment, qty 5 for each of the 4 sizes)
  • VNZ-12 Vacuum Pick-Up Nozzle,12mm, Reflow Head
  • VNZ-08 Vacuum Pick-Up Nozzle, 8mm, Reflow Head
  • VNZ-05 Vacuum Pick-Up Nozzle, 5mm, Reflow Head
  • VNZ-01 Vacuum Pick-Up Nozzle, 1mm, Reflow Head
  • AC-RP Nozzle Removal Pad
  • 20987 CSP Adjustable V Block
  • 19782 BGA Adjustable V Block
  • KAP-100 Pre-cut Kapton Tape (qty 100)
  • SRS-OVK Optical Verification Kit
  • UBS-SRS Under Board Support
  • PNZ-07 Vacuum Pick-Up Nozzle, 0.7mm O/D, Fine Placer
  • PNZ-24 Vacuum Pick-Up Nozzle, 2.4mm O/D, Fine Placer
  • PNZ-60 Vacuum Pick-Up Nozzle, 6.0mm O/D, Fine Placer
 

Scorpion upgrade kits available: 

APR-SRS-UK2 - Contactless IR Sensor

APR-SRS-UK3 - Side View Camera 

 

Download the latest version of the Scorpion software V1.12 for new features and bug fixes. V1.10 is also available in 12 languages : English, French, German, Italian, Spanish, Japanese, Traditional Chinese, Simplified Spanish, Korean, Russian, Polish and Vietnamese.

 

DOWNLOAD DATA SHEET


REQUEST HELP


Accessories

Upgrade

Consumables

Spare Parts

Filters

  Metcal is a brand of

  

   © 2017 Metcal. All rights reserved 

   Privacy PolicyCode of Business Conduct | Supplier Code of Conduct Terms & ConditionsSite Map    


 

Visit our other brand sites

Quant 3D
techcon